ER-X Quick Start Guide (2024)

EdgeRouter X

Power Adapter (12V, 0.5A)

• For indoor applications, use Category 5 (or above) UTP cabling approved for indoor use.
• For outdoor applications, shielded Category 5 (or above) cabling should be used for all wired Ethernet connections. To enhance ESD protection, attach a ground wire (not included) to the back panel of the EdgeRouter.

  We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti. For more details, visit: ui.com/toughcable

	Note: Although the cabling can be located outdoors, the EdgeRouter itself should be housed inside a protective enclosure.

Power Options

The EdgeRouter can be powered by either method:

• Power adapter
• 24V passive PoE on the eth0/PoE In port

Passive PoE output on port eth4/PoE Out works as a passthrough and depends on the input power source.

If the included Power Adapter (12V, 0.5A) is used, there may not be sufficient passthrough to power another device because the EdgeRouter can consume up to 5 watts on its own.

We recommend using a more powerful input power source (not included); here are a few examples of viable power input options for passive PoE passthrough:

* Not compatible with 24V, 1A Gigabit PoE Adapter.

Power LED
Off	Power Off
Green	Power On
Link/Activity LED (eth0 - eth4 Ports)
Off	No Link
Green	Link Established at 10/100/1000 Mbps Flashing Indicates Activity
eth0/PoE In Port
RJ45 port accepts 24V passive PoE and supports a 10/100/1000 Ethernet connection.
eth1 - eth3 Ports
RJ45 ports support 10/100/1000 Ethernet connections.
eth4/PoE Out Port
RJ45 port supports passive PoE passthrough and a 10/100/1000 Ethernet connection.
Reset Button
Click here to learn how to reset the EdgeRouter to factory defaults.
Ground
ESD grounding for enhanced ESD protection. The ground wire and screw with washer are not included (recommended screw size: M3-0.5 x 4 mm).
Power Port
Connect the Power Adapter.

Follow the appropriate instructions:

Connecting Power Using the Power Adapter

Connecting Power Using PoE

OR

The EdgeOS® configuration interface can be accessed via DHCP or static IP address assignment. By default, eth1 is set up as a DHCP client, while eth0 is assigned a static IP address of 192.168.1.1. To configure the EdgeRouter, proceed to the appropriate section, DHCP or “Static IP Address”.

DHCP

1. Connect an Ethernet cable from eth1 on the EdgeRouter to a LAN segment that has an existing DHCP server.

   

2. To check the IP address of the EdgeRouter, use one of the following methods:
   • Set up the DHCP server to provide a specific IP address to the EdgeRouter based on its MAC address (on the label).
   • Let the EdgeRouter obtain an IP address and then check the DHCP server to see which IP address was assigned.
3. Launch your web browser. Enter the appropriate IP address in the address field. Press enter (PC) or return (Mac).
4. Enter ubnt in the Username and Password fields. Read the Ubiquiti License Agreement, and check the box next to I agree to the terms of this License Agreement to accept it. Click Login.

The EdgeOS Configuration Interface will appear, allowing you to customize your settings as needed. For more information, refer to the EdgeOS User Guide, which is available at ui.com/download/edgemax

Static IP Address

1. Connect an Ethernet cable from the Ethernet port on your computer to the port labeled eth0/PoE In on the EdgeRouter. If you are using PoE, then connect your computer to the EdgeRouter via a PoE switch or to the adapter’s LAN port.

   

2. Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet.
3. Launch your web browser. Type https://192.168.1.1 in the address field, and press enter (PC) or return (Mac).
4. Enter ubnt in the Username and Password fields. Read the Ubiquiti License Agreement, and check the box next to I agree to the terms of this License Agreement to accept it. Click Login.

The EdgeOS Configuration Interface will appear, allowing you to customize your settings as needed. For more information, refer to the EdgeOS User Guide, which is available at ui.com/download/edgemax

You can also manage your device using the Ubiquiti Internet Service Provider. UISP™ lets you configure, monitor, upgrade, and back up your devices using a single application. Get started at uisp.ui.com